Product Details

Product Description Open

WE BOUGHT EVERYTHING DEFIANCE HAD LEFT! GET THESE TOP TIER RECEIVERS WHILE YOU CAN, WHEN THEY ARE GONE - THEY ARE GONE - AND AT THESE PRICES, THEY WON'T LAST LONG!

***PLEASE NOTE - These actions are surplus stock, they are brand new, in the box - but have been discontinued by the manufacturer. Because these are discontinued, ALL SALES ARE FINAL and NO BACKORDERS will be accepted. Full Defiance Warranty still applies. For any questions, please do not hesitate to contact us.

WHEN WEIGHT MATTERS

Weighing as little as 19.2 oz.

If you watch your scales as closely as you watch your targets, check out the Defiance anTi action—a minimalist take on Defiance’s legendary precision actions. Weighing under 21oz. it still carries the same guaranteed headspace as the Ruckus, anTi X, Renegade and Classic with integral lug. Pre-hardened aircraft-grade 416 stainless steel receiver, paired with a chrome moly bolt. Featherweight. No compromises.

Approximate weights for complete action*
- 20.6 oz – Short (Rem. SA)
- 22.2 oz – Long (Rem. LA)
*complete action consists of stainless-steel receiver, one-piece 4340 CM bolt, handle/knob, firing pin assembly with aluminum shroud, and side bolt release
Receiver and bolt are in a stainless finish
Receiver made of pre-hardened aircraft-certified 416 stainless steel with integral recoil lug.
4340 chrome moly bolt made in one operation, enabling guaranteed headspace +/- .001″
Recessed bolt lugs, Mini-16 extractor, and plunger standard
Includes Mil Spec 1913 (Picatinny) 20 MOA scope base.
Receiver barrel threads are 1.0625” X 16 T.P.I. (Rem. 700 thread dia. and pitch)
Actions available in:
- Short (Rem. SA)
- Long (Rem. LA)
Bolt face available .390″ (.223), .480″ (.308), .545″ (.300WM)
90° Bolt Throw
Available in right hand only
Works with hinged floorplates and center feed detachable magazines

All material pre-hardened prior to machining to prevent changing tolerances during heat treat.
Bolt machined from one piece of pre-hardened 4340 chrome moly in one operation enabling guaranteed headspace +/- .001″.
Receiver machined from one piece of pre-hardened 416SS.
Wire EDM-cut, full-length lug ways result in smooth bolt operation.
Primary extraction design significantly increases initial extraction and ensures smooth bolt cycling.

Hand
- Right
Bolt Face
- .223 Rem (.390)
- .308 Rem (.480)
- .300 WM/RUM (.545)
Magazine Cut
- BDL for use with hinged floorplate or center feed magazines (Wyatt’s cut)

Extensively machined Receiver body with integral recoil lug
Bolt stop/side bolt release, spring, pin
Extra light one-piece bolt
anTi Deep bolt fluting
Mini-16 extractor
Hollow anTi bolt knob
Fluted firing pin/spring
Cocking piece
Aluminum bolt shroud
Trigger pins

MUST SHIP TO A FFL

Red Hawk Rifles LLC. will transfer ownership of any firearm/receiver ONLY to individuals or agencies in possession of a valid Federal Firearms License (FFL). We cannot ship to individuals without a valid FFL.
It is the buyer’s responsibility to check and comply with local, state, and federal laws. The buyer assumes all legality, liability and responsibility for the condition, use & security/storage of the firearm/receiver purchased.
It is the buyer’s responsibility to contact the FFL dealer. Be aware that it is customary for your local dealer to charge a transaction fee at the time you pick up your purchase.This transfer fee is strictly between you and your local dealer. It is your responsibility to check with your local dealer concerning any policy of this kind and concerning your obligations.
You the buyer are responsible for forwarding a copy of the FFL and all pertinent contact information to Red Hawk Rifles LLC. FFL’s can be sent to:

Email: sales@redhawkrifles.com
Fax: 970-242-6177

Shipping Open